1,3-Disubstituted imidazolium ionic liquids have been the subject of numerous theoretical and experimental studies due to their low viscosity-often the very lowest for any given cation/anion family. One of the mysteries in the imidazolium family of salts is the sharp increase in viscosity that is observed on methylating at the C2 position in the ring. In the nonmethylated case, the C2 proton is observed to be distinctly acidic and, where this is undesirable, substitution of the C2 position removes the problem, but produces an unexpected increase in viscosity. Methylation at other positions on the ring does not produce such a significant effect. In this study, two possible structural or energetic sources of the increased viscosity were investigated:(1) ion association, as probed by the Walden rule, and (2) differences in the potential energy surface profiles that favor ionic transport in the non C2-methylated imidazolium ionic liquids. The second hypothesis was investigated using high-level ab initio theory. The higher viscosity of C2-methylated imidazolium ionic liquids is shown to be a result of high potential energy barriers (significantly above the available thermal energy) between the energetically preferred conformations on the potential energy surface, thus restricting movement of ions in the liquid state to only small oscillations and inhibiting the overall ion transport.

We describe a porphyrin dye-sensitised solar cell utilising a solid state electrolyte containing the I(-)/I(3)(-) redox couple, which yields a performance of 5.3% under moderate light intensity and 4.8% at full sun.

A one-pot synthesis of 2,6-dibromodithieno[3,2-b;2',3'-d]thiophene (dibromo-DTT, 4) was developed. A key step was bromodecarboxylation of DTT-2,6-dicarboxylic acid, obtained by saponification of the diester 1. The donor-acceptor dye DAHTDTT (13), based on a central 2,6-bis[2'-(3'-hexylthienyl)]dithieno[3,2-b;2',3'-d]thiophene core (9), was prepared and incorporated in a dye-sensitized solar cell (DSC), which exhibited an energy conversion efficiency of 7.3% with V(oc) of 697 mV, J(sc) of 14.4 mA/cm(2), and ff of 0.73 at 1 sun.

High-performance, room-temperature (RT), solid-state dye-sensitized solar cells (DSSCs) were fabricated using hierarchically structured TiO₂ nanofiber (HS-NF) electrodes and plastic crystal (PC)-based solid-state electrolytes. The electrospun HS-NF photoelectrodes possessed a unique morphology in which submicrometer-scale core fibers are interconnected and the nanorods are dendrited onto the fibers. This nanorod-in-nanofiber morphology yielded porosity at both the mesopore and macropore level. The macropores, steming from the interfiber space, afforded high pore volumes to facilitate the infiltration of the PC electrolytes, whereas the mesoporous nanorod dendrites offered high surface area for enhanced dye loading. The solid-state DSSCs using HS-NFs (DSSC-NF) demonstrated improved power conversion efficiency (PCE) compared to conventional TiO₂ nanoparticle (NP) based DSSCs (DSSC-NP). The improved performance (>2-fold) of the DSSC-NFs was due to the reduced internal series resistance (R(s)) and the enhanced charge recombination lifetime (τ(r)) determined by electrochemical impedance spectroscopy and intensity modulated photocurrent/photovoltage spectroscopy. The easy penetration of the PC electrolytes into HS-NF layers via the macropores reduces R(s) significantly, improving the fill factor (FF) of the resulting DSSC-NFs. The τ(r) difference between the DSSC-NF and DSSC-NP in the PC electrolytes was extraordinary (~14 times) compared to reported results in conventional organic liquid electrolytes. The optimized PCE of DSSC-NF using the PC electrolytes was 6.54, 7.69, and 7.93% at the light intensity of 100, 50, and 30 mW cm⁻², respectively, with increased charge collection efficiency (>40%). This is the best performing RT solid-state DSSC using a PC electrolyte. Considering the fact that most reported quasi-solid state or nonvolatile electrolytes require higher iodine contents for efficient ion transport, our HS-NFs are a promising morphology for such electrolytes that have limited ion mass transport.

Electrodeposition of poly(3,4-ethylenedioxythiophene) onto conducting plastic allows the cheap and facile synthesis of plastic cathodes for dye-sensitised solar cells, having excellent solar cell efficiency (8%), at a fraction of the cost of platinised plastic.

Ionic liquid electrolytes based on a number of imidazolium, quaternary ammonium and phosphonium cations have been developed for porphyrin dye sensitised solar cells yielding efficiencies of up to 5.2% at 0.68 Sun.

The exothermic behaviour and intrinsic safety of a number of ionic liquids being considered for battery and solar cell applications have been investigated at elevated temperatures by analysing data from accelerated rate calorimetric (ARC) studies.